AISI 304L austenitic stainless steel, with the chemical composition shown in Table 1, was provided in the form of a hot-rolled and annealed sheet of 20 mm thickness. The LCF investigation was carried out on the material in two states: i) as-received, further referred as AR state, and ii) after additional solution annealing (SA state) performed at …
Abstract This study reports the influence of diffusion kinetics on the interfacial microstructure and its significance in the mechanical properties of the diffusion bonded titanium (Ti) to 304L stainless steel (SS). The surface finished commercially pure Ti (ASTM grade-2), and 304L SS rods were diffusion bonded at three different temperatures …
AISI 304 – industrially denoted as 18/8, is an austenitic chromium-nickel stainless steel. The tag of AISI on it stands for (American Iron and Steel Institute), identifying its commercial availability of stainless steel or chromium steel. AISI 304 stainless steel composition mainly consists of 18% chromium and 8% nickel, and other stainless
Table 6 displays the AISI 304L reaction for material removal rate (MRR) within the three levels of each selected input parameter in this study. The highest values of MRR were achieved in abrasive waterjet contour cutting of AISI 304L, with 421.2 mm³/min for 4 mm, 767.10 mm³/min for 8 mm, and 811.4 mm³/min for 12 mm material thicknesses.
A comprehensive analysis of the erosion–corrosion behavior of AISI 304L stainless steel immersed in 0.5 M NaCl solution with the addition of industrial tailing particles obtained from the copper mining industry is reported. From fundamental studies using combined measurements of potentiodynamic and weight loss techniques, the pure …
The aim of this study is to investigate the low-cycle fatigue (LCF) properties of an AISI 304L welded joint based on experimental data. The influential parameters on the LCF such as the specimen thickness, strain ratio and cryogenic temperature were considered in this experimental study. In order to investigate the thickness effect on the …
Type 304L Stainless Steel. Type 304L stainless steel is an extra-low carbon version of the 304 steel alloy. The lower carbon content in 304L minimizes deleterious or harmful carbide precipitation as a result of welding. 304L can, therefore, be used "as welded" in severe corrosion environments, and it eliminates the need for …
The monotonic and cyclic deformation behavior of ultrafine-grained metastable austenitic steel AISI 304L, produced by severe plastic deformation, was investigated. Under monotonic loading, the martensitic phase transformation in the ultrafine-grained state is strongly favored. Under cyclic loading, the martensitic transformation …
Plasticity-induced martensitic transformation during cyclic deformation of AISI 304L stainless steel Mater. Sci. Eng. A, 114 (Jul. 1989), pp. L11-L16, 10.1016/0921-5093(89)90871-X View PDF View article View in Scopus Google Scholar [16] I. …
Two types of wrought AISI 304 steels, namely AISI 304 or 304L, and a niobium stabilized grade AISI 348 have been studied in the present work. The AISI 304-type steel was delivered in three forms: (i) cold-drawn cylindrical bar of 20 mm in diameter, hot-rolled 6 mm thick plate (1D finish) and cold-rolled 1 mm thick sheet (2B finish); AISI 348 …
AISI 304L / UNS S30403 / DIN 1.4307 Low Carbon Austentic Stainless Steel Alloy 304L is an extra low carbon version of type 304 chrome-nickel austenitic alloy. It is typically used for welded applications that must resist intergranular corrosion. It is strong, light
Abstract. Specially designed billets of AISI 304L stainless steel were forged at two temperatures, 843 °C and 941 °C, and with varying transfer times. The machined 304L billets were thick near the center (51 mm) and thin near the periphery (10 mm) such that forging with a flat platen resulted in regions of high strain (center) and low strain